{"id":1288,"date":"2015-10-19T11:59:33","date_gmt":"2015-10-19T02:59:33","guid":{"rendered":"https:\/\/kyo-tatami.com\/lib\/?page_id=1288"},"modified":"2017-09-29T15:25:15","modified_gmt":"2017-09-29T06:25:15","slug":"saisun","status":"publish","type":"page","link":"https:\/\/kyo-tatami.com\/world\/saisun\/","title":{"rendered":"Measurement"},"content":{"rendered":"\r\n
\r\n\r\n

What do we mean we hen we say we have to take measurements?<\/h3>\r\n
\r\n
\r\n

To create tatami that fits without gaps and has clean lines it is critical we measure the space. No room is perfectly square and any slight mis-calculation means the tatami won’t fit.
\r\nTatami measurement is taken differently to a general carpenters or an architectural measurement.<\/p>\r\n<\/div>\r\n

\r\n
\r\n\"Measurement\"\r\n<\/div>\r\n<\/div>\r\n<\/div>\r\n\r\n

Why should measurements be taken?<\/h3>\r\n

Often customers say:
\r\n\u201cWhy is it necessary to make measurements while we have the design drawing of the room?\u201d
\r\n\u201cOur room is Kyo-ma (room for Kyoto size tatami), so size is determined already.\u201d
\r\n\u201cOur house is new, so it seems unnecessary to measure the size again.\u201d<\/strong>
\r\nWe can not guarantee it will fit without measuring the space. Each tatami has its own place in the room and is created to reflect that so it sits flush.<\/p>\r\n\r\n

\r\n
\r\n

Your room does not have perfect 90 degree angles.<\/h4>\r\n

All rooms have some differences in size or angle of the corners compared with the size written on the design drawing. However good the carpenter may be, he or she can never build the house in the precisely same as the design.<\/p>\r\n

Normally, the precise size of your room doesn\u2019t matter. But in order to cover the space with tatami, without gaps, an exact measurement is necessary. This is for old and new architecture, as well as space that has already had tatami laid.<\/p>\r\n\r\n<\/div>\r\n

\r\n
\r\n\"Examples

Examples of some distortions of a room (that cause differences in sizing)<\/p>\r\n<\/div>\r\n<\/div>\r\n<\/div>\r\n\r\n

What happens if tatami is made without taking measurements?<\/h3>\r\n
\r\n
\r\n

Making tatami without taking precise measurements will cause problems when tatami are installed. Gaps may be present and this makes the tatami look unfinished and uneven. This is due to the difference in size, a corner not at 90 degrees, weight bearing posts sitting out from the wall, or slight curve of the wall.<\/p>\r\n\r\n

There will be some space between tatami and the wall.<\/h4>\r\n

Without taking precise measurements and installing tatami to cover the whole room, there definitely will be some space\/gaps between the wall.<\/p>\r\n

If there is a space between tatami and the wall, it will gather dusts and encourage bugs. If the tatami can move it will be damaged and uneven, causing a tripping hazard.<\/p>\r\n

Tatami has some shrinkage as it ages so if there are gaps they will increase in size as time goes on.\r\n<\/p>\r\n\r\n

Tatami cannot be installed.<\/h4>\r\n

If the room is smaller than expected, or it has protrusions or curves, obviously tatami cannot be installed in the room.\r\nYou may think, \u201ctatami is so soft that it can be pushed in\u201d. But by doing so, igusa will be put under extreme strain, which leads to further damage.<\/p>\r\n

In case tatami cannot be installed, it has to be remade \u2013 increasing costs.<\/p>\r\n

*We very rarely make tatami without taking the measurement but if the client insists we can not guarantee it will fit, and strongly advise against forgoing the measurement process.\r\n<\/p>\r\n<\/div>\r\n

\r\n
\r\n\"There
\r\n

There happens to be a gap due to differences in size or angle, and unable to install tatami<\/span><\/p>\r\n<\/div>\r\n

\r\n\"Due
\r\n

Due to the curve or projection, there may be some gaps, and tatami cannot be installed.<\/span><\/p>\r\n<\/div>\r\n<\/div>\r\n<\/div>\r\n

\r\n